UPQ-D1 Loa nguồn điểm 15" Meyer Sound
Tính năng nổi bật
|
ACOUSTICAL1 |
|
|
Operating Frequency Range2 |
55 Hz – 18 kHz |
|
Frequency Response3 |
58 Hz – 18 kHz ±4 dB |
|
Phase Response |
80 Hz – 18 kHz ±45° |
|
Linear Peak SPL4 |
135.5 dB with crest factor >17 dB (M-noise), 132 dB (Pink noise), 135 dB (B‑noise) |
|
COVERAGE |
|
|
|
80° horizontal x 50° vertical (‑6 dB) 100° horizontal x 60° vertical (‑10 dB) |
|
TRANSDUCERS |
|
|
Low Frequency |
One high‑power 15‑inch cone driver with neodymium magnet; 2 Ω nominal impedance |
|
High Frequency |
One 4‑inch diaphragm compression driver; 8 Ω nominal impedance |
|
AUDIO INPUT |
|
|
Type |
Differential, electronically balanced |
|
Maximum Common Mode Range |
±15 V DC, clamped to earth for voltage transient protection |
|
Connectors |
XLR 3‑pin female input with male loop output; optional 5‑pin connectors to accommodate both balanced audio and RMS signals |
|
Input Impedance |
10 kΩ differential between pins 2 and 3 |
|
Wiring |
Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 2: Signal + Pin 3: Signal ‑ Case: Earth ground and chassis |
|
Nominal Input Sensitivity |
0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music |
|
Input Level |
Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker. |
|
AMPLIFIER |
|
|
Type |
Two‑channel, Class‑D |
|
Total Output Power5 |
2250 W peak |
|
THD, IM, TIM |
< 0.02% |
|
Cooling |
Convection |
|
AC POWER |
|
|
Connector |
PowerCON 20 input with loop output |
|
Automatic Voltage Selection |
90–265 V AC, 50–60 Hz |
|
Safety Agency Rated Voltage Range |
100–240 V AC, 50–60 Hz |
|
Turn‑on and Turn‑off Points |
90 V AC turn‑on; no turn‑off; internal fuse‑protection above 265 V AC |
|
CURRENT DRAW |
|
|
Idle Current |
0.27 A rms (115 V AC); 0.25 A rms (230 V AC); 0.29 A rms (100 V AC) |
|
Maximum Long‑Term Continuous Current (>10 sec) |
2.0 A rms (115 V AC); 1.0 A rms (230 V AC); 2.3 A rms (100 V AC) |
|
Burst Current (<1 sec)6 |
3.7 A rms (115 V AC); 1.9 A rms (230 V AC); 4.3 A rms (100 V AC) |
|
Maximum Instantaneous Peak Current |
8.2 A pk (115 V AC); 4.2 A pk (230 V AC); 9.3 A pk (100 V AC) |
|
Inrush Current |
< 20 A peak |
|
RMS NETWORK (OPTIONAL) |
|
|
|
Equipped with two‑conductor twisted‑pair network, reporting all operating parameters of amplifiers to system operator’s host computer. |